Skip to content

Preparation of High-Performance Copolyamide 6 via a Side-Methyl Topological Structure Design Strategy

Aug 2026 · Industrial & Engineering Chemistry Research · Vol 65, pp. 18910-18923 · 0 citations · 40 references

Abstract

To address the insufficient toughness and transparency of nylon-6 (PA6) caused by high crystallinity, this study proposes a copolymer strategy based on side-methyl structural regulation. A series of PA6/D6 copolyamides were prepared via in situ melt copolymerization of ε-caprolactam, 2-methyl-1,5-pentanediamine, and adipic acid, enabling high-value utilization of the MPMD byproduct. Structural analyses confirmed incorporation of D6 units, whose steric hindrance weakened hydrogen bonding, promoting transformation from the ordered α-form to the γ-form and reducing lamellar and spherulitic ordering. This resulted in lower melting/crystallization temperatures with good thermal stability, expanding the processing window, while restricted chain slippage increased melt viscosity and elasticity. Increasing D6 content enhanced ductility and transparency: PA6/D60.2 achieved elongation at break exceeding 1000% with high tensile strength, while PA6/D60.3 showed the highest transmittance. This work elucidates the mechanism of side-methyl steric hindrance on PA6′s structure, offering a strategy for tough, transparent, processable copolyamide 6.

View source

Similar papers

Sep 2026

Active Segment Polymerization of 1,3-Propanediamine Enables Low-Melting-Point Polyamides for High-Precision 3D Printing

The preparation of ultra-short-chain diamine-based polyamides by melt polycondensation remains a formidable challenge in polyamide synthesis, with 1,3-propanediamine (DAP) serving as a representative monomer. To date, the fundamental reasons why this monomer fails to yield satisfactory polymeric products via melt pol...

Lu-Rong Zhang, Hang-Tao Song, Yang Zhou et al. · 0 citations
Oct 2026

Development of Thiophene-Based Copolyesters with a High Gas Barrier and Toughness by the Introduction of Diethylene Glycol

A bio-based poly (butylene thiophenedicarboxylate-co-diethylene glycol) (PBThD) copolyester was synthesized with 2,5-thiophenedicarboxylic acid (TDCA), 1,4-butandiol (BDO), and diethylene glycol (DEG). The free rotation of the ether bond in DEG is used to give the molecular chain good flexibility, and then combined w...

Xiao-Qin Jiang, Ji-Yang Zuo, Mei-Ling Chen et al. · 0 citations
Oct 2026

Crystallization during Polymerization: A Route to Low-Entangled Solid-State Processable Ultra-High-Molecular-Weight trans -1,4-Polybutadiene

Trans-1,4-polybutadiene (TPBD) is a material of commercial interest whose properties strongly depend on its trans isomer content. The polymer exhibits distinctive features, including a highly linear backbone without pendant groups, excellent dynamic performance, low rolling resistance, low heat buildup, good strength...

Nasser Sharahili, Jia-Yi Zhao, J. van der Eem et al. · 0 citations
Oct 2026

A Hydrazide-PEG Bifunctional Crystallization Promoter Enables Strong, Tough, and Storage-Stable P34HB

Poly[(R)-3-hydroxybutyrate-co-4-hydroxybutyrate] (P34HB) is a biodegradable polyester with attractive processing potential, but its slow crystallization and storage-induced secondary crystallization compromise its mechanical performance. Here, di(polyethylene glycol)-bis(succinohydrazonoyl) oxalate (BSO-PEG) was desi...

Jian Wang, Wan-Ning Ren, Xue-Wei Wei et al. · 0 citations
Sep 2026

Vanillin-Derived Polybisbenzoxazine: Tailoring Mechanical Performance and Circularity via Dynamic Imine Chemistry

Traditional petroleum-based thermosetting polybenzoxazines face significant environmental challenges due to their nonrecyclability and dependence on fossil resources. In this study, a series of fully biobased, imine-cross-linked polybisbenzoxazine networks (VD-Cx) were successfully synthesized using a vanillin-derive...

Jin-Ling Li, Shu-Hao Liang, Yang-Guang Xiang et al. · 0 citations

We use cookies to run the site and, with your consent, for analytics and to show ads. See our Cookie Policy.